Mares NEMO AIR Guide de l'utilisateur télécharger pdf (Page 4)

Nemo Wide dive computer

HOW THE NEMO WIDE DIVE

COMPUTER WORKS

The Nemo Wide has 8 operating modes:

1. DIVE

2. WATCHSET

3. TIME

4. PC

5. LOGBOOK

6. PLANNING

7. SET DIVE

8. OFF

Press any button to turn on Nemo Wide; the

word “DIVE” will appear.

At this point you can easily navigate through

the computer functions using the four keys

(Fig. 1).

Fig. 1

The buttons are used the same way in every

operating mode:

• the <+> button moves forward

• the <-> button moves backward

• the <ENTER> button accepts the selection

• the <ESC> button does not accept the

selection, or it exits the current operative

mode to return to the previous menu.

CHECK THE LEVEL OF BATTERY CHARGE

Nemo Wide periodically checks the charge

remaining in the batteries. The charge level

can be viewed in OFF mode (Fig. 2).

Fig. 2

If a low charge level is detected (20%), the

battery icon turns on and the display backlight

function is disabled.

When the icon ﬁrst appears, replace the

battery as soon as possible.

If the charge level drops to the minimum value

(5%), all Nemo Wide functions are disabled,

and only the OFF mode can be accessed.

 WARNING

When the computer has not been used

for a long time, we recommend that you

check the battery status and replace it if

necessary.

BACKLIGHTING

Pressing the <+> button for two seconds will

temporarily turn on the backlight (for about 4

seconds).

•

 WARNING

Temperature can noticeably affect battery

voltage. The icon that signals a low battery

level may appear due to low temperatures,

even if the battery still has sufﬁcient

capacity. In this case, backlighting is

disabled.

If backlighting has been disabled due to low

temperature, you can repeat the battery

status check by entering OFF mode (Fig. 2). If

the battery icon disappears, the backlighting

function has been re-enabled.

 WARNING

We advise that you replace the battery if

you intend to dive in cold water.

AUTOMATIC SWITCHOFF

If Nemo Wide is switched on but you don’t

press any buttons for a certain period, it will

switch off automatically.

The delay before automatic switch-off varies

depending on the current operating mode.

SETTING PARAMETERS FOR THE

NEMO WIDE DIVE COMPUTER

ADJUSTING THE WATCH:

WATCHSET

The WATCHSET menu, (Fig. 3), is divided into

three submenus, where you can adjust the

following parameters:

ADJ TIME

time

watch display (12h-24h)

date

Key Beep

turn key sounds on or off

Contrast

Display contrast

Fig. 3

From the main menu, use the <+> or <-> keys

to select WATCHSET mode. Pressing the

<ENTER> button will display the words “ADJ

TIME”.

WATCHSET  ADJ TIME

Pressing the ENTER button will enter this

mode. Use the <+> or <-> buttons to adjust the

values: press and release the button to change

the value by one unit at a time, or hold down

one of the buttons to scroll automatically.

Press the <ENTER> button to save the changes

made and move to the next selection.

The <ESC> button exits to the previous set.

After making our selection we ﬁnd ourselves

back in the ADJ TIME menu. Use the <+> and

<-> buttons to move to the Key Beep menu.

•

WATCHSET  KEY BEEP

Press the ENTER button to access this mode,

where you can use the <+> and <-> buttons to

select whether or not you want to hear a sound

when you press the keys.

Press the <ENTER> button to accept the

selection:

After the changes have been made, the

computer returns to the Key Beep menu. Use

<+> and <-> to move to the Contrast menu.

WATCHSET  CONTRAST

Pressing the ENTER button will enter this

mode, and it will display the current contrast

value. This can be changed using the <+> or

<-> keys.

Press the <ENTER> button to accept the

selection.

After the changes have been made, the

computer returns to the Contrast menu.

Pressing the <ESC> button will exit this menu

and the computer goes back to the main

WATCHSET menu.

ADJUSTING DIVE PARAMETERS:

SET DIVE

In this menu you can set the general data and

operational modes for the dive. SET DIVE has

two submenus:

Set dive - Data

Set dive - Mode

In the SET DIVE - DATA mode you can change

the following parameters:

salt / freshwater

meters – degrees Celsius / feet – degrees

Fahrenheit

Clear residual nitrogen

In the Set dive - Mode menu you can change

the following parameters as a function of the

type of dive selected.

Air

Altitude

Personal correction factor

Uncontrolled ascent

Audible alarms

EAN

Percentage O

Maximum PPO

Altitude

Personal correction factor

Uncontrolled ascent

Audible alarms

Bottom time

Audible alarms

From Main Menu, use the <+> or <-> buttons

to select SET DIVE mode. Press the <ENTER>

button to display the word “DATA” (Fig. 4).

Fig. 4

Press <ENTER> to enter the set.

1 2 3 4 5 6 7 8 9 ... 13 14

Commentaires sur ces manuels

Pas de commentaire

Mares NEMO AIR Guide de l'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour PC/postes de travail Mares NEMO AIR